Kwam laatst nog tot een verschil, maar vergeten te posten:
De one spot wordt een stuk warmer dan de Godlyke! Geen idee waar het verschil in zit, maar je zou er een kaasfondue warm op kunnen houden..
Printable View
Kwam laatst nog tot een verschil, maar vergeten te posten:
De one spot wordt een stuk warmer dan de Godlyke! Geen idee waar het verschil in zit, maar je zou er een kaasfondue warm op kunnen houden..
Ideaal! Kaasfondue heerscht!Citaat:
Oorspronkelijk geplaatst door Nielsje
Ik heb Cioks aangeschreven en gelijk gevraagd of mijn Sennheiser EW100 G2 wireless syteem ook op de Double Jack kan:Citaat:
Oorspronkelijk geplaatst door HaroldAling
"Hi,
Well, the Double Jack is definitely a good choice for your setup. Good thinking!
Unfortunately I can't give you any guaranties that you won't get any noise, hiss or hum caused by possible ground loops. In 95% cases there are no problems at all. But as I said I can't say for sure. The best thing would be to try it out.
If the wireless system really needs 300mA you won't find any isolated PSU that would do the job. If the actual current draw is lower you are able to buy my competitors product which is 2-3 times more expensive and bigger in size and weight. I would give it a try with the Double Jack.
Good luck!
Med venlig hilsen / best regards,
Poul Ciok"
Double jack it is!
Staat hier nou niet dat ik gewoon die 1 spot met de POD kan gebruiken?Citaat:
How does the 1 SPOT work with Line 6 modeling pedals? Don't they require AC and use 1200mA of current?
Well, it does say "9VAC 1200mA" on the back of the Line 6 pedals, but they don't really use that. That is simply the output rating of the POD adapter which the modeling pedals also use. If you think about it, the Line 6 pedals take batteries, don't they? Batteries are DC, not AC, so the pedals must really run on DC voltage. So how do they work with a 9VAC POD adapter? The modeling pedals have a bridge rectifier at the power input jack which immediately converts AC to DC where the adapter plugs in. And regarding the 1200mA of current the pedals are supposedly using, it's really more in the range of 350mA. That's still more than an average adapter can handle, but the 1 SPOT can handle two Line 6 pedals and have plenty of juice left over for several ordinary stomp boxes. Why Line 6 didn't come out with a separate adapter for the modeling pedals, I don't know, but the 1 SPOT makes an excellent alternative to the bulky single-purpose POD adapter.
Ze hebben de One Spot normaal gesproken toch ook bij Feedback ? Kan 'm nergens vinden op de site.Wel bij Music Store, maar daar doet de site het momenteel niet goed van. Of NLM ? Daar kom ik zaterdag zo ongeveer langs...
Volgens mij hebben ze die dingen bij alledrie genoemde zaken.
Maar waarom? Je had toch een Godlyke?!
Idd Mitch de One Spot staat niet bij vreedbeck op de site maar ze hebben um wel in de winkel (bij ons in Eindhoven iig, en ik neem aan ook bij de andere filialen) want ik heb de mijne gewoon bij feedback gekocht (ik had zelf ook eerst op de site gekeken maar kon toen ook niks gevonden krijgen)Citaat:
Oorspronkelijk geplaatst door Mitch
Groetjes en succes,
Anthony
Ik ken de Line6 pedalen niet (en al helemaal niet van binnen), maar zou het kunnen dat deze gast denkt dat jij het over de tone core pedaaltjes van Line6 hebt? Misschien gebruiken die minder stroom... Ik hoop dat je eerst een second opinion vraagt...Citaat:
Oorspronkelijk geplaatst door Chief
edit: ff op de Line6 site gekeken, in de XX4 pedalen gaan idd ook batterijen.
Als je bij Feedback rotterdam een onespot wil halen moet je het ff aan de kassa de vragen, die ligt gewoon achter de kassa. Ik heb hem ook bij Feedback vandaan.Citaat:
Oorspronkelijk geplaatst door Mitch
Dat staat er letterlijk inderdaad.. Als dit een betrouwbare bron is zou ik t wel aandurven zonder second opinion, want ik denk dat dat wel klopt wat er gezegd wordt.Citaat:
Oorspronkelijk geplaatst door Chief
grt Roy.