PDA

View Full Version : Afstellen elementen



Robin.ke
12 mei 2007, 23:39
Ik heb vandaag een OLP MM1 "voor erbij"gekocht. Ik wilde graag wat experimenteren D-tune zonder dat ik weer een halve dag moet pielen aan mijn Jackson met floyd-rose. Hij valt me tot nog toe 100% mee, prima gitaartje in z'n prijsklasse.
Nu ben ik bezig om de afstelling naar mijn smaak te zetten. Het valt mij hierbij op dat de elementen ver onder de snaren liggen in vergelijking met mijn Jackson. Met mijn (beperkte) logische denkvermogen zou ik zeggen dat: hoe kleiner de afstand des te hoger de output. Als ik ze verstel, hoor ik geen wezenlijk verschil. Iemand enig idee wat de ideale afstand is ?

The Underdog
12 mei 2007, 23:46
de ideale afstand is deze die jij mooi vindt klinken. In mijn gitaren vind ik wel serieuze verschillen tussen de hoogte.

Damage Inc.
13 mei 2007, 00:02
Over pickups en afstellen èh:

Ik heb bij sommige pickups, vooral op de brugpositie, als ik eroverheen beweeg of erop steun dat ze heel erg openeer bewegen.

Kan ik die niet vaster zetten ofzo?
Of buigt het metaal waarmee ze "gemount" zijn gewoon heel erg?
Dat idee heb ik in ieder geval wel...

DarknessAwaits
13 mei 2007, 01:59
Je pickups zitten aan schroeven met veertjes normaal gesproken, dus er is altijd wat speling:

http://www.warmoth.com/guitar/options/images/pickup_routing_humbucker.gif

De hoogte-afstelling van je pickups is persoonlijk, maar er zijn 2 dingen waar je rekening mee moet houden: hoe dichter bij de snaren hoe meer output maar ook méér string-pull waardoor je rare verschijnselen krijgt in de trilling van de snaar. Hij trilt dan niet meer 'vrij' en dan krijg je al snel dat het zaakje niet meer zuiver klinkt.

Damage Inc.
13 mei 2007, 02:47
Ik moet er (voor mijn probleempje) wel even bij zeggen, dat ik met 'op en neer' niet zeg maar naar binnen en naar buiten of omhoog en omlaag bedoel.
Maar echt dat de pickups heen en weer bewegen, net alsof ze los in de gaten liggen.
Ok, de meeste zitten goed vast, die bewegen bijna echt niet, maar een paar zitten erg los.
Naar mijn kennis en ook aan die tekening te zien, zou ik niet weten hoe ik ze vaster zou kunnen zetten.

Het valt me wel op dat die pickups met kapjes, zoals ik ook met gouden kapjes en EMGs heb, minder bewegen dan de open versies.
Dat zal natuurlijk zijn omdat ze dan minder ruimte hebben en makkelijker vast tussen de ringen kunnen zitten.
Daarnaast heb ik ook nog een gitaar met open pickups, zonder pickup-ringen en dan zijn de gaten nog eens extra groot ook.
Maar die pickups zitten nog redelijk vast...

The Underdog
13 mei 2007, 03:07
Dat van die string pull geldt alleen voor alnico pickups als ik mij niet vergis en dan nog vind ik die verhalen sterk overdreven.

DarknessAwaits
13 mei 2007, 14:21
Dat jij niet kunt begrijpen dat magneten invloed hebben op hoe snaren trillen is jouw probleem.


You can explore from a pickup height setting with a high volume amp setting OR with the pickups at maximum height with lower volume amp settings. Some players prefer one or the other and some prefer inbetween so PLEASE experiment and try both approaches.

Maximum height:

Set the gap at the neck pickup (both E strings only) to 2mm or 5/64", but not less than that.

Set the gap at the middle pickup (both E strings only) to 2mm or 5/64", but not less than 1.75mm or 1/16"+.

Set the gap at the bridge pickup (both E strings only) to 1.5mm or 1/16", but not less than that.

To get a workable volume balance between the neck and bridge pickups I suggest you adjust the bridge pickup to your desired sound. Then adjust the neck pickup so it balances. Occasionally we have to put up with a little bit of imbalance to get the sound we want from each pickup, this is normal.

Minimum height:

Set the pickups almost level with the pickguard and raise a little at a time until you discover where your sweet spot is. Take care not to let the pickup drop off the end of the screw. If this happens the only way to get the screw started again is to take the pickguard off.

NOTE: If you use less than the recommended gap measurement the sound will be abrasive and harsh and we wouldn't want that now would we, or would we? ALSO these gap distances assume the vibe arm is depressed and not raised. If you pull up on the arm you'll need to increase the gaps accordingly or else the strings will bottom onto the magnets.

Increasing the gap will reduce output level and brightness, some people will like that but others won't, so experiment to get the effect you want. Remember that even 1/4 turn of the adjusting screws can make the difference. And don't be afraid to lower the pickups almost to the pickguard and turn the amp volume up.

You can do things like optimize the neck pickup for loud lead work, the middle for softer rhythm and the bridge for bright twang, bite and growl, or any other responses you would like. Another nice rhythm sound can be achieved by setting the neck pickup down more on the bass side (3mm) than the treble (2.5mm). The in-between sound (2 pickups on simultaneously) can be varied to a surprising degree. For maximum hollowness in pos 2 or 4, set the pickups as above, but for more quack/bite adjust the middle pickup away from the strings. You make the rules here, so experiment!!!

Kinman pickup adjusting screws are the two best tone controls you could wish for, and so much better than relying on the volume or tone controls to tune your sound.

My pickups are more responsive than any other pickup to these settings and a wide variety of tonalities can be achieved by messing around with them. Spend a little time exploring this whole new world of tone and fine tuning your sounds one pickup at a time, the effort will be well worth while. And don't be discouraged if it takes some time, I've heard of players finally achieving their goals up to 2 or 3 weeks on.
STRAT-ITIS explained (Strat-itis = simultaneous multiple discordant frequency syndrome).

Dirty or rusty strings can also do this but many players know this horrible phenomena is caused by excessively strong magnets in the pickups, here's how it works. What happens is the magnets of the pickups pull a section of the string (the part that's over the pickups) into a U shaped vibration path. Normally the strings vibrate in what is essentially a single-plane path or pattern. Lets say that the time taken for a string (not subjected to excessive magnet pull) to complete one cycle or oscillation is X milliseconds. Traveling in a U shaped path it actually takes longer to complete one cycle or oscillation since the distance is greater via the U shaped path, so the time is X + Y milliseconds. Now it's getting clear that what you have is a string that has a section of it's length vibrating in a U shaped path and part of the remaining section raveling in a direct single-plane path and yet other sections traveling at all frequencies between these two extremes. This means that the three sections are actually vibrating at many different frequencies when the string should be vibrating uniformly at a single frequency. What happens when you mix all these different frequencies together? Uggghhh, dissonant Strat-itis that's what! It's bad enough hearing 2 non-harmonious notes coming from a single string, but when you get multiple dissonant frequencies (or notes) being produced simultaneously from a single string the results are absolutely ghastly. A string that's out of tune with itself no less. That's what Strats do when you adjust the pickup magnets close to the strings. But when you adjust them to prevent Strat-itis, output, sensitivity and dynamic range are reduced and noise is increased when the Amp's Volume is turned up to compensate.

Fortunately Kinman Strat* and Tele*pickups utilize a unique magnet technology that reduces the string pull of Alnico-5 by around 35% and virtually eliminates the multiple note syndrome in Stratocasters. This is not magnet aging or degaussing, this is something new, something unique to Kinman.

Robin.ke
13 mei 2007, 14:24
De hoogte-afstelling van je pickups is persoonlijk, maar er zijn 2 dingen waar je rekening mee moet houden: hoe dichter bij de snaren hoe meer output maar ook méér string-pull waardoor je rare verschijnselen krijgt in de trilling van de snaar. Hij trilt dan niet meer 'vrij' en dan krijg je al snel dat het zaakje niet meer zuiver klinkt.

Ik heb nog even de twee uiterste standen van de elementen uitgeprobeerd (helemaal onderop en vlak onder de snaren). Dicht onder de snaren levert inderdaad een wat hogere output op, maar het klinkt naar mijn idee wat rommeliger. Jouw theorie lijkt wel te kloppen. Ik ga nog even zoeken naar een ideale hoogte

DarknessAwaits
13 mei 2007, 20:27
:sssh: Is niet mijn theorie hoor ;)

Het makkelijkst is om te beginnen met een vrij lage stand en dan alsmaar wat verder omhoog draaien. Als je dan het idee hebt dat je de sweetspot voorbij bent, gewoon een slagje terug.