HaroldA
10 september 2013, 20:38
Jullie weten onderhand wel dat ik alles geloof wat er op het Internet staat en ik kwam laatst dit stukje (http://www.sonicdeli.com/ThunderTweakWeb/plexi_mods.htm) tegen:
11) our friend Master Volume
Now that another triode of gain has been added, which is a lot, we need a way to control how much signal hits our splitter. Otherwise any little turn of the gain knob would produce truly stupid amounts of volume. This is where the master volume comes in. Looking at the 2204 schematic we can see, after the treble knob, there's a 1M master volume control feeding the input of the splitter. They call this a "pre-phase inverter"-type master. I like it a lot because I can drive the preamp as hard as I feel the need and have control over how much signal hits the input of the splitter and balance the preamp/poweramp overdrive. When you think of it this way it gives a finer control over the whole amp's tone and feel.
Some folks don't like this type of master because it sounds thin at low volumes or it doesn't sound the same at every volume. The easy fix is to add a 100k-220k resistor between the 1M pot and the input of the splitter. Boom, a master volume that sounds great at all levels! My turret boards even have a spot for this resistor!
Nou ben ik natuurlijk geneigd om dit direct uit te voeren op al mijn MV amps, maar toch wringt dit een beetje. Ik heb al een hele hoop schema's bekeken, en of ik heb er helemaal overheen gekeken, of dit wordt helemaal nergens gebruikt? Ik heb alleen dit stukje (https://sites.google.com/site/yourtubeamp/mods-and-maintenance/-master-volume-controls) kunnen vinden:
Kevin O'Connor has a good explanation in The Ultimate Tone about how this affects the tone of the amp. When the preamp signal is attenuated, some treble is lost. The more attenuation, the more treble that is lost. A series resistor of about 100K can help reduce this effect, but you'll lose a little volume.
Daar wordt een 100k aangeraden om het verlies in hoog tegen te gaan, ten koste van een beetje volume, maar dat kun je weer oppeppen door je master hoger te zetten ;)
Is een 100-220k weerstand in serie met de wiper van de volumepot onzin, of eigenlijk best een goed idee? Heeft er al iemand ervaring mee?
11) our friend Master Volume
Now that another triode of gain has been added, which is a lot, we need a way to control how much signal hits our splitter. Otherwise any little turn of the gain knob would produce truly stupid amounts of volume. This is where the master volume comes in. Looking at the 2204 schematic we can see, after the treble knob, there's a 1M master volume control feeding the input of the splitter. They call this a "pre-phase inverter"-type master. I like it a lot because I can drive the preamp as hard as I feel the need and have control over how much signal hits the input of the splitter and balance the preamp/poweramp overdrive. When you think of it this way it gives a finer control over the whole amp's tone and feel.
Some folks don't like this type of master because it sounds thin at low volumes or it doesn't sound the same at every volume. The easy fix is to add a 100k-220k resistor between the 1M pot and the input of the splitter. Boom, a master volume that sounds great at all levels! My turret boards even have a spot for this resistor!
Nou ben ik natuurlijk geneigd om dit direct uit te voeren op al mijn MV amps, maar toch wringt dit een beetje. Ik heb al een hele hoop schema's bekeken, en of ik heb er helemaal overheen gekeken, of dit wordt helemaal nergens gebruikt? Ik heb alleen dit stukje (https://sites.google.com/site/yourtubeamp/mods-and-maintenance/-master-volume-controls) kunnen vinden:
Kevin O'Connor has a good explanation in The Ultimate Tone about how this affects the tone of the amp. When the preamp signal is attenuated, some treble is lost. The more attenuation, the more treble that is lost. A series resistor of about 100K can help reduce this effect, but you'll lose a little volume.
Daar wordt een 100k aangeraden om het verlies in hoog tegen te gaan, ten koste van een beetje volume, maar dat kun je weer oppeppen door je master hoger te zetten ;)
Is een 100-220k weerstand in serie met de wiper van de volumepot onzin, of eigenlijk best een goed idee? Heeft er al iemand ervaring mee?